More product photos
Your first MagniGlide setup
MagniGlide Complete Kit
5.0 / 5· 1 customer reviewPermanent bases, replaceable wool-felt glide pieces and mounting hardware. One complete glide per furniture leg.
Stubby drill bit included for pre-drilling
For suitable wooden legs: straight or slightly angled, not heavily angled. Check the approximately 1″ (26 mm) mounting diameter.
U.S. standard shipping: $8 below $35; free at $35+ after discounts. Taxes excluded.
Ships in 1–2 business days. Unused returns within 30 days. Shipping details · Returns
Measurements & compatibility
Size & fit
Overall diameter: approximately 1″ (26 mm). Felt diameter: approximately 1″ (24 mm).
Complete assembled height, uncompressed: approximately 11/16″ (17 mm). The complete assembly settles to just under 5/8″ (approximately 15 mm) in height after 2–4 weeks of normal use, leaving approximately 3/16″ (5 mm) of felt extending below the protective cup.
For furniture with suitable wooden legs or mounting surfaces. Screwdriver required for initial installation; no tools needed for replacement. Already have bases? Shop refills
Useful product details
What is included?+
Your selected pack contains 4, 8 or 16 permanent bases, matching replaceable floor-contact pieces with wool felt, and mounting hardware. These cover 1, 2 or 4 standard four-legged chairs.
Stubby drill bit included for pre-drilling
How does replacement work?+
Catch the edge of the glide and pull it away by hand. Snap a fresh piece onto the installed base. The magnets stay in the base; the replaceable piece connects through its steel interface.
Floor care and compatibility+
Designed for common finished hard surfaces such as wood, laminate, luxury vinyl and tile. Test first and inspect regularly. Keep felt free of trapped grit. Confirm furniture-leg suitability before installing the screw-mounted base.
Full product description+
Install Once. Replace Only What Wears.
Install the permanent base once. Replace only the floor-contact piece when it wears.
MagniGlide is a two-piece magnetic furniture-glide system designed to eliminate the repeated work and expense of replacing an entire furniture glide every time the felt wears out.
Each complete MagniGlide unit consists of:
- A permanent screw-mounted base that stays secured to the furniture leg
- A removable floor-contact assembly that attaches magnetically to the installed base
- High-density felt bonded inside a recessed protective housing
- Mounting hardware for the initial installation
Stubby drill bit included for pre-drilling
One complete MagniGlide unit is installed on each furniture leg.
During the initial installation, the permanent base is secured to the furniture. After that, the base is designed to remain in place. When the felt becomes worn, dirty, or damaged, the customer does not remove the screw, replace the base, scrape off adhesive, or reinstall an entirely new glide.
Simply catch the edge of the removable floor-contact assembly, pull it away from the base, and snap a replacement back into place.
The permanent base stays. The replaceable floor-contact piece is the part that gets renewed.
MagniGlide is designed to protect hardwood, tile, laminate, and luxury vinyl plank flooring while making routine furniture-glide maintenance faster, cleaner, and less expensive.
Why MagniGlide?
- Install the permanent hardware once
- No repeated screwing and unscrewing
- No peeling adhesive pads
- No scraping away old glue
- No digging worn felt out of a plastic holder
- No stiff friction tabs or special removal tools
- Replace the floor-contact assembly in seconds
- Pay substantially less for future replacement refills
Lower Long-Term Replacement Cost
The initial complete system includes the permanent base and the removable floor-contact assembly.
Stubby drill bit included for pre-drilling
After the system is installed, replacement pieces cost only $1.10 to $1.30 each, depending on pack size.
Buy the complete system once. Future replacement pieces start at just $1.10 each.
Every complete glide includes the permanent screw-mounted base and the replaceable floor-contact glide piece with high-density virgin wool felt.
The expensive hardware stays installed. You replace only the part that wears.
Complete kits include the permanent screw-mounted bases and matching replaceable floor-contact glide pieces with high-density virgin wool felt.
Stubby drill bit included for pre-drilling
Once the system is installed, replacement-only packs let customers renew the wearing floor-contact pieces without purchasing the permanent bases again.
Replacement pieces cost $1.10 to $1.30 each, depending on pack size.
Already have MagniGlide installed? Shop lower-cost replacement pieces starting at $1.10 each.
Product Dimensions
- Total assembled height: 17 mm uncompressed, settling to approximately 15 mm after 2–4 weeks of compression.
- Overall diameter: 26 mm.
- Felt glide diameter: 24 mm.
Height measurements are for the complete assembled system, including the mounted base and felt glide.
U.S. Patent No. 12,144,423 B1. Watch MagniGlide in action